12 Easy Ways to Reduce Water Heater / Geyser Power Consumption

Rate this post

Water is a synonym for life. However, changing the temperature of the water is essential as well. Thus, water heaters and geysers are necessary, but at times these become too heavy for the electricity bill. Here are some easy ways to reduce water heater/ geyser power consumption.

Geysers and Power Consumption

We need hot water for several purposes. Moreover, if it is winter, then hot water is the only saviour. Therefore, using hot water while not burdening on the electricity bill is essential. Here are some easy ways to do so therefore, give it a reading.

Storage Tank Insulation

Insulate your storage tank. It helps in reducing heat loss. Moreover, it also helps in preventing the unit from frequently turning it on.

However, do not forget to follow the manufacturer’s instructions. It might include not covering the heater’s thermostat, burner, top and bottom.

Moreover, contact your local plumber to insulate the hot water tank.

Installing Heat Traps

Using heat traps let the flow of cold water into the tank. However, it prevents the heated water and the unwanted convection from flowing from the unit. 

There are many modern heaters that are designed with in-built heat traps. However, if your unit is more than 10 years old, installing a heat trap is a better option.

Have a talk with your professional plumber for more information.

Lowering the Thermostat

Typical households are comfortable with 120 degrees Fahrenheit. However, the manufacturers set the water heater thermostats at 140 degrees Fahrenheit.

Therefore, before taking a shower, make sure to adjust it. You will not notice any substantial difference. 

Reducing the temperatures by 20 degrees cuts the appliances’ energy consumption by 10 %.

However, on the other hand, this adjustment cuts cost. Besides, it reduces scalding. Also, it slows up the mineral build-up and corrosion in the pipes and the heater.

Draining the Tank

Draining your water heater once a year counts as a good practice. It removes those sediments that obstructs the heat transfer and reduces the efficiency of the unit.

However, make sure to follow the instructions of the manufacturers. If necessary, you can even call a professional well.

Insulating the Pipes

Along with insulating the tank, insulating the pipes is a good option. If you add insulation in the first 6 feet of hot and cold water pipes, it prevents fire hazards.

Also, it conserves heat, and your system does not have to reheat it again.

Installing a Timer

If you install a timer that turns off your heater after the heating is done, saves a lot of energy. There will be no unnecessary wastage of electricity then.

Also, it adds years to the unit’s life. Just call your local plumber to assist you in the process.

Make Use of Cold Water

This sounds very obvious. However, it is an effective tip. Using cold water for essential grooming and laundry purposes cuts down your bill.

Moreover, using cold water is healthy as well.

Replace Old Water Heaters and Buy New Ones

If your water heater is more than 10 years old, it is better to replace it with a new energy-efficient water heater.

The old water heater also might get burst or leaked. Therefore, it is a better idea to replace the old one with the new one.

Fix the Leaks

Repair the leaks. It might sound like a minor issue. However, it wastes a lot of water and money within a very short time. Therefore, repair them immediately.

Recirculating System

If you need to run the faucet for a long time before you get hot water, add a recirculating system. This system speeds up the hot water delivery. As a result, you waste less water and spend less.

Low-flow Fixtures

If you are having shower heads and faucets, made before 1992 then replace them with low-flow ones. The modern ones use half the water used by the older ones.

By doing this, you can save 25-60% of water.

Do not Run Water Unnecessarily

It is a very widespread mistake that people make. Do not run water unnecessarily. Close the tap when not in use. Often people let the water run while they are about to use it.

However, run the water only when you are using it instead of wasting by running the water unnecessarily beforehand.

Tips to Maintain the Water Heater / Geyser

Apart from the tips to lower energy consumption and save water, here are some tips for maintaining your water heater. 

If you maintain your water heater properly, the life of your water heater gets extended. Moreover, it enhances the efficiency as well.

Therefore, continue reading and follow them.

  • You must flush a quart of water from the tank. Do it at an interval of 3 months.
  • The temperature and pressure valve must be checked every 6 months.
  • Always replace anode rods. However, it depends on the type of water as to how frequently you should replace.
  • For solar water heater systems, a solar contractor must check.
Reduce Water Heater Power Consumption

Bottom Line

Thus, to conclude, if these tips are followed properly, your water heater will survive more, and your electricity bill will be a bit lighter.

However, along with relieving your electricity bill, do not forget saving water is essential. It is the basis of life.


Water Heater Tank Material and Coating – Everything You Need to Know!

Everything You Need to Know About TDS Controller/ Modulator in a Water Purifier


Leave a Comment